# p. 1

every item shown here is only one prim leaf rez a sphere

[close]

# p. 2

set size to x=0.500 y=0.250 and z=0.370 set path cut to b=0.000 and e=0.500 set hollow to 95.0 set twist to b=180 and e 180 two leaves rez a sphere set size to x=0.500 y=0.300 and z=0.300 set path cut to b=0.700 and e=1.000 set hollow to 95.0 set twist to b=360 and e=47 set dimple to b=0.100 and e=0.950 use these two options to differentiate leaves sizes

[close]

# p. 3

flat leaf raindrop rez a sphere set size to x=0.500 y=0.500 and z=0.010 set twist to b=360 and e 360 set dimple to b=0.000 and e=0.050 if you want to have a flat leaf contour set hollow to 85.0

[close]

# p. 4

claw rez a torus set size to x=0.430 y=0.500 and z=0.500 set path cut to b=0.500 and e=1.000 set taper to x=1.00 and y=1.00

[close]

# p. 5

flower i rez a tube set size to x=0.070 y=0.350 and z=0.350 set twist to b 360 and e=360 set hole size to x=1.00 and y=0.50

[close]

# p. 6

flower ii rez a sphere set size to x=0.010 y=0.500 and z=0.500 set twist to b=360 and e 360 set dimple to b=0.000 and e=0.050

[close]

# p. 7

ribbon i rez a sphere set size to x=0.010 y=0.500 and z=0.500 set hollow to 95.0 set twist to b 360 and e=360 set dimple to b=0.700 and e=1.000

[close]

# p. 8

ribbon ii rez a sphere set size to x=0.035 y=0.500 and z=0.500 set path cut to b=0.130 and e=0.870 set hollow to 50.0 set twist to b 360 and e=360 set dimple to b=0.450 and e=0.550

[close]

# p. 9

infinity symbol rez a sphere set size to x=0.500 y=0.500 and z=0.010 set hollow to 95.0 set twist to b=0 and e 360 set dimple to b=0.000 and e=0.050

[close]

# p. 10

spring i rez a torus set size to x=0.100 y=0.500 and z=0.500 set skew to 0.80 set twist to b 18 and e=0 set hole size to x=0.70 and y=0.05 set taper to x=1.00 and y=0.00 set radius to 1 but it will change to 0.947 so you can also just put this number in set revolutions to 2.50

[close]

# p. 11

spring ii rez a torus set size to x=0.500 y=0.300 and z=0.300 set skew to 0.80 set hole size to x=0.10 and y=0.05 set revolutions to 4.00

[close]

# p. 12

spring iii rez a torus set size to x=1.000 y=0.150 and z=0.150 set skew to 0.45 set twist to b=360 and e 360 set hole size to x=0.15 and y=0.05 set revolutions to 4.00

[close]

# p. 13

string rez a torus set size to x=2.300 y=0.500 and z=0.500 set hollow to 80.0 set skew to 0.80 set twist to b=360 and e=360 set hole size to x=0.05 and y=0.50 set profile cut to b=0.180 and e=0.200 set taper to x=0.00 and y=0.50 set revolutions to 4.00

[close]

# p. 14

knot rez a torus set size to x=2.500 y=0.500 and z=0.500 set hollow to 95.0 set skew to 0.95 set twist to b 90 and e=360 set hole size to x=0.05 and y=0.50 set profile cut to b=0.180 and e=0.200 set revolutions to 4.00

[close]

# p. 15

double knot rez a torus set size to x=2.500 y=0.500 and z=0.500 set hollow to 95.0 set skew to 0.95 set twist to b 360 and e=360 set hole size to x=0.05 and y=0.50 set profile cut to b=0.180 and e=0.200 set taper to x=0.00 and y=0.50 set revolutions to 4.00

[close]